Home
Aluminium Oil/Petrochemical Power/Incineration Cement/Mineral Glass/Ceramics Ferrous/Non-Ferrous
 
Our Products > Low Cement Castables
 

Our Products

Quick Jump
Sort this list by
Armorkast 65AL

DESCRIPTION:
Armorkast 65AL is a 65% Alumina low cement dense castable that is non wetting to Aluminium Metal. It can be vibrocast or pumped into place.


APPLICATIONS:
Aluminium furnace hearths, ramps, sidewalls, troughs, ladles and crucibles.

Full data sheet click here



Contact Us For Details

Armorkast 80AL Adtech

DESCRIPTION:
Armokast 80AL Adtech is an 80% alumina, low cement, low moisture castable characterised by its high density, low porosity and high hot and cold strength for use in aluminium contact applications.

 
APPLICATIONS:
Used for aluminium furnace hearths, ramps, sidewalls,troughs,ladles and crucibles.

Full data sheet click here



Contact Us For Details

Armorkast Xpur/AL Adtech

DESCRIPTION:
Armorkast Xpur/AL Adtech is an 90% alumina, low cement, low moisture castable characterized by its high density and low porosity for use in aluminum contact applications.


APPLICATION:
Low Cement, Low Moisture Castable

Full data sheet click here



Contact Us For Details

Corex Express

DESCRIPTION:
Corex Express is a self flowing, abrasion resistant, thermal shock resistant castable. It gives outstanding resistance to conditions such as rapid heating or rapid cooling, and vibration is not required to remove air voids. It can either be pumped or cast. 
 

APPLICATIONS:
Typical applications are tunnel kiln cartops, annealing furnace cars, carbon anod baking furnace flue port exhaust block, carbon anode baking furnace burner blocks, FCCU transfer lines, reactor riser, regenerator overhead lines, stand pipe, spend catalyst lines, seal pot, wet ash hoppers and water quench regions of industrial processes.

Full data sheet click here



Contact Us For Details

Express 30

DESCRIPTION:
Express 30 is a dense free flowing hydraulic bonded castable refractory suitable for use to 1650°C. It has the unique property of not requiring vibration for placement or to remove air. It can be cast or pumped, to produce a lining having a very good abrasion resistance.


APPLICATIONS:
Typical applications include FCCU transfer lines, cyclones, air heaters, aluminium furnace upper sidewall and roofs, precast shapes, burner blocks rotary kiln lifter and mixer shapes, rotary kiln feed and discharge hoods, brass crucible furnace tops, brass reverbatory furnace upper sidewalls and roofs, vertical case of channel induction furnaces melting yellow brass, incinerators, high temperature boiler linings and combustion chambers.

Full data sheet click here



Contact Us For Details

Greenkleen 60 Plus

DESCRIPTION:
Greenkleen 60 Plus is a 60% Alumina vibratable low cement castable. Greenkleen 60 displays outstanding abrasion wear and thermal shock resistance. It is formulated to be non wetted by Aluminum.


APPLICATIONS:
Greenkleen 60 is specifically designed for Aluminum contact. Typical applications include furnace floors, lower sidewalls etc.

Full data sheet click here



Contact Us For Details

Greentec 170 LG

DESCRIPTION:
Greentec 170 LG is a unique, truly low cement gun mix, exhibiting high hot strength.


APPLICATIONS:
Greentec 170 LG is a premium low cement gunning product with excellent strengths, very good abrasion resistance, high hot strength and good thermal shock resistance. Suitable for use in any arduous environment eg. petrochemical industry, incineration, cement kilns and various steel applications.

Full data sheet click here



Contact Us For Details

Grefcote 70 AL Plus

DESCRIPTION:
Grefcote 70 AL Plus is a 70% AI2O3 low cement gunning mix for aluminium applications that can be installed hot or cold.
 

APPLICATIONS:
Used for gunned repairs in aluminium furnaces and ladles.

Full data sheet click here



Contact Us For Details

Thor AZSP Adtech

DESCRIPTION:
Thor AZSP Adtech is a premium, low moisture, fused zirconia-mullite refractory for use in cement production.

Features include excellent strength and abrasion resistance, low thermal conductivity, low permeability, inert to alkalies, resists buildup and clogging.
Installation versatility allows material to be vibration-cast or pumped.


APPLICATIONS:
Cement preheaters, feed inlets, and calciners Feed shelves in wet process kilns Nose Rings Risers

Full data sheet click here 



Contact Us For Details

Ultra Green 45

DESCRIPTION:
Ultra Green 45 is a ultra low cement castable suitable for use at temperatures up to 1650°C. It exhibits high density and low porosity, outstanding hot load bearing capability and superior corrosion resistance. 


APPLICATIONS:
Ultra Green 45 can be used as an original lining material or as a material to repair existing linings. It is used as pre-cast shapes in a range of iron and steel applications, non-ferrous furnaces and ladles. Other market applications include cement kilns, and chemical processing.

Full data sheet click here



Contact Us For Details

Ultra Green 57A

DESCRIPTION:
Ultra Green 57A is a 57% Alumina, Andalusite based dense, ultra low cement castable suitable for use up to 1650°C.Ultra Green 57A has outstanding thermal shock resistance. Ultra Green 57A also features high hot strength and low porosity equal to comparable fired brick formulations.


APPLICATIONS:
Typical applications include incinerators, calciners and other areas where extreme cyclic temperature conditions occur.

Full data sheet click here



Contact Us For Details

Ultra Green 70 Adtech

DESCRIPTION:
Ultra Green 70 Adtech is a 70% alumina, ultra-low cement, vibratable castable. This product features excellent strength, oustanding hot load bearing ability, superior corrosion resistance and low porosity - high density.
 

APPLICATIONS:
Can be used as an original lining material and to repair existing linings. This product can be used for pre-cast shapes in iron and steel applications, non-ferrorus furnaces and ladles. Also used in cement kilns, coolers and nose rings and in the chemical processing industry.

Full data sheet click here



Contact Us For Details

Ultra Green 80

DESCRIPTION:
Ultra Green 80 is a general purpose 80% Alumina ultra low cement castable with high hot strength, abrasion resistance and resistance to hot metal corrosion.


APPLICATIONS:
Ultra Green 80 is used in most industrial markets as a general purpose vibro cast ultra low cement castable. These markets include, iron and steel, cement, chemical processing, incineration etc. Specific applications include cement nose rings and cyclones, electric arc delta sections and furnace hearths

Full data sheet click here



Contact Us For Details

Ultra Green 80 AL

DESCRIPTION:
Ultra Green 80 AL is an 80% Alumina, vibratable ultra low cement castable. It has very high strength, high hot load bearing ability, low porosity and high density.Ultra Green 80 AL is specially formulated for resistance to corrosion by molten aluminium.


APPLICATIONS:
Ultra Green 80 AL is specially designed for the severest aluminium contact applications.

Full data sheet click here



Contact Us For Details

Ultra Green SR

DESCRIPTION:
Ultra-Green SR is a tabular alumina based, 86% alumina, ultra-low cement, vibrating castable. This product desplays high hot strength for resistance to hot load deformation and hot abrasion. Maximum operating temperature is 1870°C. Its addition of andalusite gives it thermal shock resistance superior to conventional ultra-low cement tabular alumina castables.


APPLICATIONS:
Applications include, but are not limited to immersion lances for molten steel refining, impingement pads, electric furnace roofs, and high temperature incinerator linings.

Full data sheet click here



Contact Us For Details

Ultra-Express 70 AL

DESCRIPTION:
Ultra-Express 70 AL is a 70% Alumina free flowing, ultra low cement dense castable that is non wetting to Aluminium metal.


APPLICATIONS:
Typical applications for Ultra-Express 70 AL in the Aluminum Industry include furnace hearths, lower side walls and belly band regions. It is also used in ramps and upper sidewalls, launders and troughs, ladles and tap or drain blocks.

Full data sheet click here



Contact Us For Details

Versaflow 45 Plus

DESCRIPTION:
Versaflow 45 Plus is a fireclay based low cement castable for use in high abrasion environments up to 1482°C. Good volume stability resulting in less shrinkage cracking in service.


APPLICATIONS:
Iron and Steel Foundries - Reheat furnaces, forge furnace car decks.
Minerals Processing Rotary Kilns - Lifters, feed-end and chain sections, cooler walls.
Chemical Processing Industry - Boiler applications, incineration (ash hoppers).
Aluminium - Flue caps, precast shapes for carbon bake furnaces, subhearths and lower sidewall back-up castable.

Full data sheet click here



Contact Us For Details

Versaflow 45/AL Adtech

DESCRIPTION:
Versaflow 45/AL Adtech is a fireclay low cement castable, designed specifically for aluminium metal contact applications and back-up linings. Contains AL inhabitor for increased metal penetration resistance. Flowable feature enables material to be vibcast, poured or pumped with slight adjustments to water content.
 

APPLICATION:
Used for primary back-up linings in lower sidewalls, hearths of aluminium melting and holding furnaces. Can also be used in metal contact applications such as lower sidewalls, hearths, ramps, door sills/jambs, troughs and transport crucibles.

Full data sheet click here



Contact Us For Details

Versaflow 55/AR Adtech

DESCRIPTION:
Versaflow 55/AR Adtech is a 55% Alumina low cement castable based on Alabama bauxitic calcines for use in high alkali and abrasion environments. Can be installed in several ways – from vibcast consistency to pump casting techniques.


APPLICATIONS:
Aluminum Furnaces - Upper sidewalls and roofs, diecast furnaces.
Steel Industry - Ladle covers, tundish covers.
Cement Industry – Preheater maintenance.
Incineration - Charging zones, burners, rotary kilns.

Full data sheet click here



Contact Us For Details

Versaflow 57A

DESCRIPTION:
Versaflow 57A is a 57% Alumina, Andalusite based dense, ultra low cement castable suitable for use up to 1650°C.


APPLICATIONS:
Versaflow 57A has outstanding thermal shock resistance in applications having extreme cyclic temperature conditions. Versaflow 57A also features high hot strength and low porosity equal to comparable fired brick formulations.

Full data sheet click here



Contact Us For Details

Versaflow 60 Plus

DESCRIPTION:
Versaflow 60 Plus is a 60% Alumina low cement castable which can be installed in several ways - from vibcast consistency to pump casting techniques. Versaflow 60 Adtech has excellent abrasion resistance, high hot strengths and high refractoriness.


APPLICATIONS:
Ceramic Kilns - Car decks exposed to high temperatures and thermal cycling.
Aluminum Furnaces - Upper sidewalls and roofs. Steel Industry - Ladle covers, tundish covers, tundish safety lining and precast shapes for tundishes. Rotary Kilns - Nose rings, lifters, firing hoods, coolers and preheater maintenance. Incineration - Charging zones, burners, rotary kilns.

Full data sheet click here



Contact Us For Details

Versaflow 65/AL Plus

DESCRIPTION:
 Versaflow 65/AL Plus is a 65% Alumina low cement castable designed specifically for aluminium metal contact applications. Contains aluminium inhibitor for increased metal penetration resistance and has high hot strength at 815°C.


APPLICATIONS:
Aluminium – Metal contact applications including lower sidewalls and hearths, ramps, door cills / jambs, troughs and transport crucibles, diecast furnaces.

Full data sheet click here



Contact Us For Details

Versaflow 70/CU Adtech

DESCRIPTION:
Versaflow 70/CU Adtech is a 70% Alumina low cement castable specifically designed for copper and iron foundry applications. Stronger than conventional castables and ramming mixes used in copper service. Contains a special penetration inhibitor which provides increased resistance to attack by molten metal and slags. High hot strength at 1370°C. Installation versatility enables material to be vibcast, conventionally cast or pumped with slight adjustment to water content.


APPLICATIONS:
Copper - Copper launders, shaft furnace repairs, anode spoons. Iron Foundries - Replacing plastics or other castables in foundry ladles.

Full data sheet click here



Contact Us For Details

Versagun 50 Adtech

DESCRIPTION:
Versagun 50 Adtech is a 50% alumina low cement gun mix combining high density and strength with excellent gunning characteristics.


APPLICATIONS:
Used in applications requiring high strength and abrasion resistance. Typical applications include cement kiln preheaters, lime kilns, incineration and other industrial applications.

Full data sheet click here



Contact Us For Details

Versagun 60 Adtech

DESCRIPTION:
Versagun 60 Adtech is a 60% alumina low cement gunning mix with excellent strengths, very good abrasion resistance and improved refractoriness and hot strengths.


APPLICATIONS:
Used in incinerators, minerals processing rotary kilns, coolers and preheaters and a variety of industrial applications. VERSAGUN GUNNING MIXES are designed to be used with traditional gunning equipment and H-W HYDROMIX Nozzle, making small and large jobs cost effective. The H-W HYDROMIX Nozzle is an excellent addition to the standard equipment, minimising dust and rebounds.

Full data sheet click here



Contact Us For Details

Versagun 70/AL Adtech

DESCRIPTION:
Versagun 70/AL Adtech is a high strength 70% alumina gun mix based on hard fired calcined kaolins and a reduced cement content. Contains “AL” inhibitor for increased resistance to aluminium metal penetration.


APPLICATIONS:
Used in gunning applications requiring high strength, abrasion resistance and aluminium penetration resistance, such as aluminium furnace repairs to lower sidewalls, belly bands, ramps, door jambs etc. Excellent maintenance product for aluminium furnaces.

Full data sheet click here



Contact Us For Details

Versagun ABR Plus

DESCRIPTION:
Versagun ABR Plus is a 60% alumina lower cement gunning mix based on hard fired calcined kaolins.

It has excellent strengths and very good abrasion resistance.


APPLICATIONS:
Use in CFB''s, incinerators, taconite furnaces, minerals processing rotary kilns, coolers and preheaters and a variety of industrial applications.

Full data sheet click here



Contact Us For Details





Home   Aluminium   Oil/Petrochemical   Power/Incineration   Cement/Mineral   Glass/Ceramics   Ferrous/Non-Ferrous   New Products   Engineered Products   Our Products         Contact Information   User Registration